#Samsung clp 300 manual full#
#Samsung clp 300 manual free#

Replace the toner waste cartridge and test everything out. Remove the piece of paper at the plastic tab, and then hold onto the axle and push the left plastic locker to its old position. Now you will rotate the axle away from you (which should be easier), and position everything like at the beginning. Push the plastic shell back in with the small protrusions first, then you can push the entire thing to have it lock into the plastic tabs. What I did was remove the belt, and since it was a symmetrical shape, I just flipped it over, so the old surface is switching places with a new surface.ДЎ1. You don't want to turn the belt inside out. After that, everything should be free.ДЎ0. The other side of the rubber belt (opposite the tabs) is somewhat locked into the plastic shell, so you have to use some force to lift it away. You want to have this positioned towards the bottom because you need room to access the entire rubber belt.Д©. You'll find two flexible tabs that lock the plastic shells together. The plastic shell is attached to another plastic shell around the axle. The rubber belt is attached to a plastic shell. Just jiggle the axle around I held it at the central rubber thing and shook it around to rotate it.ДЁ. I found it most effective to rotate so the *top* is rotating towards you and not away from you. Rotating the axle: this will require a little bit of playing around, but should not require excessive force.

#Samsung clp 300 manual full#

The purpose of this maneuver is it will allow you to rotate the entire axle in order to gain full access to the roller.Д§. It will slide about 0.5 inches don't force it too much. Slide the locker towards the center (to the right). After you have the piece of paper all the way through, just leave it there.Д¦. I would slide a stuff piece of paper (manilla folder or business card) underneath so you are not over-flexing and snapping this tab. So use a small flat screwdriver to gently pry up this tab. It's basically L-shaped, and the axle has a small hole where the L sits inside. The left end has a tiny plastic tab protruding along the axis of the axle. There are two white plastic things at the ends. Look at the axle where the pick-up roller is attached to. for these instructions, have the front of the printer face you.ДҐ. remove imaging unit: I don't think this is necessary, what I would remove is the toner waste cartridge (open the front panel, and pull out the L-shaped object on the left side), because you don't want toner spilling all over the place.Д¤. I'm going to copy/paste his instructions and append additional details:ДЈ. Hello - I wanted to expand on what Euclides mentioned above for fixing the problem with paper feeding jams. You can write me at ehisatugo )at( gmail dot com. When repositioning the belt on the shell, observe it and put in a different position, as the slick area fits inside the shell, so a new surface is out. So, rotate it again, and so, remove the shell.Д©-I removed the rubber belt, washed it with water only. If you release them, you can remove a type of a plastic shell with the rubber belt attached to.ДЁ.1- to unlock the shell you need to rotate the axle and position the locks in a convenient way.

#Samsung clp 300 manual free#

You can move (rotate) it, if you lift and free the inside gear at left end ДЁ- at the central drumm, there is two locks, one each side. cover it.ДҐ- look at the axle of the big central rubber roller:ДҐ.1- you will see both sides have a plastic balancer and locker.ДҐ.2- left one has a small 'finger' that locks it from slide.ДҐ.3- take your cellphone and do a photo of the present position of the axle and the pieces as you will need to remember it after.Д¦-light and carefully, lift this small finger from the axle and slide the locker half inch to the center Д§- after this, you have the axlee in a so so free way. It drifted over the end of the sheet and the paper gets jammed.ДЈ- remove image unit - don not let it under sun light. In my case, the rubber roller that gets the paper was dirty with dust.